Back to 11 Pin Plug In Units
white-2-16

Power Supply Unit – PSU

R235.65

Power Supply Unit – PSU

 

Features:

 

  • Overload Protection
  • Short-circuit Protection
  • Over Temperature shut down
  • Stable supply with low ripple factor
  • Power supply ON LED
Clear selection
Category:

Description

Input Specifications

Output Specifications

Standard Output Voltage 5, 9, 10, 24 VDC
Output Power 2VA
Ripple Voltage < 2%
Overload Protection yes

Supply Specifications

Power Suppy AC Type (Galvanic) 110, 230, 400V, 525V ± 10% 50 / 60 Hz ± 5Hz
Isolation 4kV
Consumption ± 3VA
±6 VA 525 V

General Specifications

Power ON Delay ≤ 300 ms
Power OFF Delay ≤ 200 ms
Indication for
Power ON LED red
Environment
Degree Of protection IP 20
Operating Temperature -10 to + 50°C
Storage Temperature -50 to + 85°C
Weight 200g

Additional information

Supply Voltage

400Vac, 230Vac, 110Vac, 48Vac, 24Vac, 12Vac
Output

12Vdc, 24Vdc, 9Vdc, 10Vdc, 5Vdc

Reviews

There are no reviews yet.

Be the first to review “Power Supply Unit – PSU”

Related products

Pump Sequence Relay – PSR1
Pump Sequence Relay – PSR1

Pump sequence module is designed to optimize the wear on pumps, compressors or generators. The first input energizes the first pump and stores this in non-volatile memory. Subsequent inputs will energize the next output. The number of its outputs correspond to the number of outputs. After power down or no inputs activated and an input is activated, the next in the sequence of outputs is activated. This ensures balanced usesage of the pumps because the same pump is not activated at the beginning of a sequence.

 
Features:
 
  • Three normally open pressure switch inputs (voltage free)
  • Three normally open pump outputs
  • Permanent memory for next pump activated after power off
  • Output 10A SPDT
R491.90 Select options This product has multiple variants. The options may be chosen on the product page
PLUGIN-SF1_K
SF1_K Sequence Monitor with Adjustment

The SF1 Monitors negative phase sequence (NPS) voltage to detect phase failure, phase reversal and phase imbalance. The NPS voltage of the unit can be djusted from 7-15%. When any of these faults occur the unit will de-energize. The relay will only re-energize if the supply voltage corrects itself. The unit will not react to a balanced voltage variation

 
Features:
 
  • Monitoring relay for 3-phase voltage control
  • Measures if all 3 phases present and in sequence
  • Detection of phase asymmetry
  • Insusceptible to balanced supply voltage variation
  • Insensitiveto regenerated EMF
  • Fastresponse to reverse phase sequence
  • Relay ON LED
  • Output 10A SPDT
R422.02 Select options This product has multiple variants. The options may be chosen on the product page
Signal Isolator – SI120
Signal Isolator – SI120

Compact signal isolator with built-in 24VDC power supply for the output. The unit is designedd for high isolation between input, output and supply. A variety of inputs and outputs are available to suit most applications.

 
Features:
 
  • High linearity
  • Sink or Source
  • On-board PSU
  • Choice of Inputs and Outputs
  • Low cost
  • Versatile
  • Power supply ON LEDs
R1,121.79 Select options This product has multiple variants. The options may be chosen on the product page
Electro-RRP1-Tachometer
Tachometer Relay – RRP1

Thermistor motor protection unit which interfaces directly to a PTC sensor to provide protection of motors, alternators, transformers, etc. The unit will trip if the nominal trip temperature for the sensor is exceeded.

 

Microprocessor based MULTI - function tachometer relay with four selectable speeds. The unit can be selected for OVER and UNDER speeds and interfaces directly with a Namur two wire proximity sensor or limit switch.

 
Features:
 
  • Microprocessor controlled
  • Failsafe feature
  • Front face adjustable time range and function settings
  • Front face adjustable time settings
  • Modular 35.5mm DIN rail mountable
  • 0.3 – 60 hrs Adjustable time ranges
  • 8 Selectable functions
  • 10A SPDT output relay
  • LED indication for relay and power supply ON
R528.64 Select options This product has multiple variants. The options may be chosen on the product page