Back to 11 Pin Plug In Units
PLUGIN-T3M

Multi Range Instant – T3M

$40.71

Microprocessor based multi-function timer with four selectable modes of operation and time range from 0.3 sec – 60 hrs. Extensive applications due to combinations of functions and time ranges. Due to the advanced design of the unit a high accuracy can be achieved. All commonly used functions are incorporated in the unit. Any adjustment on the front potentiometer after the supply is applied is not acknowledged. This prevents unwanted changes of the time range. The instantaneous contact in the unit can be used in a hold-incircuitor where an out put is needed immediately when the supply is applied. For a unit without an instantaneous contact the T2M can be used.

 

Features:

 

  • Microprocessor based design
  • Time range 0.3sec-60hrs
  • Rear DIP switch selection of 4 functions
  • Rear DIP switch selection of 8 timer ranges
  • Potentiometer adjustable time setting
  • Repeatable deviation:<0.2%
  • Powersupply ON and Relay ON LEDs
  • Delay output 10A SPDT
  • Instantaneous output 10 A SPDT
Clear selection
Category:

Description

Time Specifications

Time Ranges
Pins 5 & 6 open 0.3-6sec
3-60sec
0.3-6min
3-60min
Pins 5 & 6 closed 0.3-6min
3-60min
0.3-6hrs
3-60hrs
Range Accuracy ≤ 0.5%
Scale Accuracy ± 5%
Repeat Accuracy ± 0.2%
Time Variation ≤ 0.05% / V
within rated power supply and ambient temperature ≤ 0.2% / °C
Reset Time 500 ms
Pulse Duration 500 ms (pins 6 & 7)

Output Specifications

Output Specifications SPDT
Rated Isolation Voltage 6000 VAC (contact / electric)
1000 VAC (contact / contact)
Nominal Rate in AC1 (AG-Ni) 1500 VA
Rated Current 5A
Rated Voltage 250V
Mechanical Life 10×106 cycles
Electrical Life 10×103 cycles (at max load)
Operation Frequency ≤ 1800 cycles/h

Supply Specifications

Power Suppy AC Type (Galvanic) 110, 230, 400V, 525V ± 10% 50 / 60 Hz ± 5Hz
Isolation 4kV
Consumption ± 3VA
±6 VA 525 V
Power Suppy DC Type (Non-galvanic) 12, 24, 48 V ± 10%
Isolation None
Consumption ± 100 mA

General Specifications

Power ON Delay ≤ 300 ms
Power OFF Delay ≤ 200 ms
Indication for
Power Supply ON LED red
Output ON LED green
Environment
Degree Of protection IP 20
Operating Temperature -10 to + 50°C
Storage Temperature -50 to + 85°C
Weight 200g

Additional information

Supply Voltage

525Vac, 400Vac, 230Vac, 110Vac, 48Vac/dc, 24Vac/dc, 12Vac/dc

Reviews

There are no reviews yet.

Be the first to review “Multi Range Instant – T3M”

Related products

PLUGIN-V1C
Voltage Monitor – V1C

The V1C is a precise UNDER / OVER voltage monitoring relay. The unit can be ordered in many AC / DC voltage ranges, making it ideal for many voltage monitoring applications.

 

The set point and hysteresis can be adjusted with separate potentiometers.

 

The unit also incorporates a latch facility to prevent undetected failures.

 
Features:
 
  • Monitoring relay for voltage control
  • Measures separate voltage input
  • Rear DIPswitch selection of UNDER / OVER voltage
  • Rear DIPswitch selection for 10sec start-up delay
  • Potentiometer adjustable voltage limits
  • Potentiometer adjustable hysteresis limits
  • Power supply ON and Relay ON LEOs
  • Latch facility incorporated
  • Output 10A SPDT relay
$33.37 Select options This product has multiple variants. The options may be chosen on the product page
PLUGIN-SC120
Signal Converters – SC120

Compact signal converter with built-in 24VDC power supply for the output. The unit is designed for low amplitude signals where isolation is not needed (use SI100 for isolation). A variety of inputs and outputs are available to suit most applications.

 
Features:
 
  • High linearity
  • On-board PSU
  • Choice of Inputs and Outputs
  • Low cost
  • Versatile
  • Power supply ON LEDs
$53.63 Select options This product has multiple variants. The options may be chosen on the product page
PLUGIN-LP2
Pump Protection Relay – LP2

Microprocessor based pump protection relay capable of protecting a submersible pump against all major power line faults. The unit calibrates itself under normal running conditions and stores these parameters in non-volatile memory. The unit also incorporates a reset delay for under current situations to enable the borehole to replenish itself. In an over current situation the unit will retry three times to prevent permanent tripping with temporary blockages.

 
Features:
 
  • Microprocessor based protection relay
  • Over / Under Current Protection
  • Over / Under Voltage Protection
  • Selectable Under Current Reset Delay
  • Three retries for Over Current
  • Automatic Self Diagnosis of Pump
  • LED indication for all faults
$42.90 Select options This product has multiple variants. The options may be chosen on the product page
Phase Sequence Monitor – SF1
Phase Sequence Monitor – SF1

The SF1 Monitors negative phase sequence (NPS) voltage to detect phase failure, phase reversal and phase imbalance. The NPS voltage of the unit can be djusted from 7-15%. When any of these faults occur the unit will de-energize. The relay will only re-energize if the supply voltage corrects itself. The unit will not react to a balanced voltage variation

 
Features:
 
  • Monitoring relay for 3-phase voltage control
  • Measures if all 3 phases present and in sequence
  • Detection of phase asymmetry
  • Insusceptible to balanced supply voltage variation
  • Insensitiveto regenerated EMF
  • Fastresponse to reverse phase sequence
  • Relay ON LED
  • Output 10A SPDT
$28.54 Select options This product has multiple variants. The options may be chosen on the product page