Back to 11 Pin Plug In Units
PLUGIN-LP2

Pump Protection Relay – LP2

$42.90

Microprocessor based pump protection relay capable of protecting a submersible pump against all major power line faults. The unit calibrates itself under normal running conditions and stores these parameters in non-volatile memory. The unit also incorporates a reset delay for under current situations to enable the borehole to replenish itself. In an over current situation the unit will retry three times to prevent permanent tripping with temporary blockages.

 

Features:

 

  • Microprocessor based protection relay
  • Over / Under Current Protection
  • Over / Under Voltage Protection
  • Selectable Under Current Reset Delay
  • Three retries for Over Current
  • Automatic Self Diagnosis of Pump
  • LED indication for all faults
Clear selection
Category:

Description

Input Specifications

Current Input Pin 6 & 10
Measuring Ranges 1 – 5A
Over Current Limit 12% (17% extended)
Recovery Time 15 sec
3 attempts then permanent OFF)
Under Current Limit 8% (12% extended)
Recovery Time 6hrs
Maximum Overload Current 10A (30 sec)
Voltage Input Pin 1 & 2
Measuring Range 160 – 260VAC
Over / Under Voltage Limit ± 15% (20% extended)
Hysteresis 5%

Output Specifications

Output Specifications SPDT
Rated Isolation Voltage 6000 VAC (contact / electric)
1000 VAC (contact / contact)
Nominal Rate in AC1 (AG-Ni) 1500 VA
Rated Current 10A
Rated Voltage 250V
Mechanical Life 10×106 cycles
Electrical Life 10×103 cycles (at max load)
Operation Frequency ≤ 1800 cycles/h

Supply Specifications

Power Suppy AC Type (Galvanic) 110, 230, 400V, 525V ± 10% 50 / 60 Hz ± 5Hz
Isolation 4kV
Consumption ± 3VA
±6 VA 525 V

General Specifications

Power ON Delay ≤ 300 ms
Power OFF Delay ≤ 200 ms
Indication for
Relay ON LED green
Power ON LED red
Over Voltage — — —
Under Voltage — ● ●
Over Current ● — —
Under Current ● ● ●
Security switch open ● — ●
Environment
Degree Of protection IP 20
Operating Temperature -10 to + 50°C
Storage Temperature -50 to + 85°C
Weight 200g

Additional information

Supply Voltage

525Vac, 400Vac, 230Vac, 110Vac

Reviews

There are no reviews yet.

Be the first to review “Pump Protection Relay – LP2”

Related products

Signal Isolator – SI120
Signal Isolator – SI120

Compact signal isolator with built-in 24VDC power supply for the output. The unit is designedd for high isolation between input, output and supply. A variety of inputs and outputs are available to suit most applications.

 
Features:
 
  • High linearity
  • Sink or Source
  • On-board PSU
  • Choice of Inputs and Outputs
  • Low cost
  • Versatile
  • Power supply ON LEDs
$78.53 Select options This product has multiple variants. The options may be chosen on the product page
Electro-LP3-Pump-protection-relay
Pump Protection Relay – LP3

Microprocessor based pump protection relay capable of protecting a submersible pump against all major power line faults. The unit calibrates itself under normal running conditions and stores these parameters in non-volatile memory. The unit also in corporate a reset delay for under current situations to enable the borehole to replenish itself. Inan over current situation the unit will retry three times to prevent permanent tripping with temporary blockages.

 
Features:
 
  • Microprocessor based protection relay
  • Over / Under Current Protection
  • Over / Under Voltage Protection
  • Phase Failure / Phase Reversal Protection
  • Selectable Under Current Reset Delay
  • Three retries for Over Current
  • Automatic Self Diagnosis of Pump
  • LED indication for all faults
$43.97 Select options This product has multiple variants. The options may be chosen on the product page
PLUGIN-ECONO-T1L_P
Pulse Interval Timer – T1I_P

Pulse Controlled Interval Timer – T1I_P

 
Features:
 
  • Single function / single time range / single voltage
  • Potentiometer adjustable time setting
  • Repeatable deviation: < 1%
  • Power supply ON and Relay ON LEOs
  • Output 10A SPDT
$34.12 Select options This product has multiple variants. The options may be chosen on the product page
PLUGIN-TP2
Two Shot Timer – TP2

Microprocessor based two-shot timer with two selectable modes of operation and eight separately selectable ON and OFF time ranges from 0.3 sec - 60 hrs. The ON and OFF times can only be selected from the A or B range and not both.

 

Extensive applications due to combination of functions and time ranges. Due to the advanced design of the unit a high accuracy can be achieved. Any adjustment on the front potentiometers after the supply is applied is not acknowledged. This prevents unwanted changes of the time range.

 

The ON and OFF times can be adjusted independently.

 
Features:
 
  • Microprocessor based design
  • Time range 0.3sec – 60hrs
  • Rear DIP switch selection of 8 separate ON and OFF timer ranges
  • Separate potentiometer adjustable time settings for ON and OFF period
  • Selectable ON or OFF time first
  • Repeatable deviation: <0.2%
  • Power supply ON and Relay ON LEDs
  • Output SADPDT
$36.50 Select options This product has multiple variants. The options may be chosen on the product page