Back to 11 Pin Plug In Units
white-2-16

Solid State Flasher – SSF1

R547.46

The solid state flasher is designed to eliminate mechanical wear and tear and arcing when switching incandescent lamps continuously. The unit also has selectable interval timing forwarning signals.

 

Features:

 

  • Microprocessor based design
  • 90 Flashes per second
  • Triac output SA 1000W/250V
  • Selectable Internal timing
  • Two complementary output
  • 95 – 230V AC supply
Clear selection
Category:

Description

Input Specifications:

Time Ranges 90 pulses per second
Range Accuracy < 1%
Repeat Accuracy ± 0.2%
Time Variation ≤ 0.5% / V
within rated power supply and ambient temperature ≤ 0.5% / °C
Reset Time 800 ms

Output Specifications

Output Specifications 90 pulses per second
Rated Isolation Voltage < 1%
Rated Current ± 0.2%
Rated Voltage < 0.5% / V
Mechanical Life < 0.5% / °C
Electrical Life —
Operation Frequency 800ms

Supply Specifications:

Power Suppy AC Type
(Galvanic)		 110, 230, 400V ±
10% 50 / 60 Hz ± 5Hz
Isolation None
Consumption ±2VA

General Specifications:

Environment
Degree Of protection IP 20
Operating Temperature -10 to + 50°C
Storage Temperature -50 to + 85°C
Weight 200g

Additional information

Supply Voltage

230Vac, 1100Vac

Reviews

There are no reviews yet.

Be the first to review “Solid State Flasher – SSF1”

Related products

Pump Sequence Relay – PSR1
Pump Sequence Relay – PSR1

Pump sequence module is designed to optimize the wear on pumps, compressors or generators. The first input energizes the first pump and stores this in non-volatile memory. Subsequent inputs will energize the next output. The number of its outputs correspond to the number of outputs. After power down or no inputs activated and an input is activated, the next in the sequence of outputs is activated. This ensures balanced usesage of the pumps because the same pump is not activated at the beginning of a sequence.

 
Features:
 
  • Three normally open pressure switch inputs (voltage free)
  • Three normally open pump outputs
  • Permanent memory for next pump activated after power off
  • Output 10A SPDT
R491.90 Select options This product has multiple variants. The options may be chosen on the product page
Pre Select Counter – XP404
Pre Select Counter – XP404

The XP404 is a fully programmable microprocessor controlled four digit counter / timer. The set value can be entered via the front membrane switch and the function, range, relay action and UP or DOWN count / time is set with an extended menu. The unit also incorporates a supply for a NPN proximity switch which can be used to pulse the counter.

 
Features:
 
  • Microprocessor based design
  • Counter/Timer function with up/down option
  • Relay On or pulse (variable) on reaching count/time
  • Front mounted membrane switch to select count
  • User friendly menu for all functions and settings
  • 4 Seven segment displays (max. Count 9999)
  • Power supply for 3 wire NPN proximity switch
  • Permanent memory for selected count
  • Reset facility incorporated
  • Output 10A SPDT relay
R770.56 Select options This product has multiple variants. The options may be chosen on the product page
Pump Seal Protection – PSP1
Pump Seal Protection – PSP1

Microprocessor based monitoring relay to measure moisture in a submersible pump. Due to the advanced design of the unit a high accuracy and safety is achieved. Response delay are incorporated to prevent nuisance tripping. The unit energises on application of supply. If the current through the probes is more than 20uA or the resistance is smaller than 10 Mohm, the relay will de-energise after 10 sec. The relay will energise if the current is less than 15uA and the resistance is more than 1.4Mohm.

 
Features:
 
  • Microprocessor based design
  • High accuracy analogue converter
  • Repeatable deviation: <0.2%
  • Power supply ON and Relay ON LEDs
  • Output 5A DPDT
R424.70 Select options This product has multiple variants. The options may be chosen on the product page
Electro-RRP1-Tachometer
Tachometer Relay – RRP1

Thermistor motor protection unit which interfaces directly to a PTC sensor to provide protection of motors, alternators, transformers, etc. The unit will trip if the nominal trip temperature for the sensor is exceeded.

 

Microprocessor based MULTI - function tachometer relay with four selectable speeds. The unit can be selected for OVER and UNDER speeds and interfaces directly with a Namur two wire proximity sensor or limit switch.

 
Features:
 
  • Microprocessor controlled
  • Failsafe feature
  • Front face adjustable time range and function settings
  • Front face adjustable time settings
  • Modular 35.5mm DIN rail mountable
  • 0.3 – 60 hrs Adjustable time ranges
  • 8 Selectable functions
  • 10A SPDT output relay
  • LED indication for relay and power supply ON
R528.64 Select options This product has multiple variants. The options may be chosen on the product page