Back to 11 Pin Plug In Units
Electro-T1R-Temperature-controller

Temperature Controller – T1R

R591.36

Temperature control unit or a standard three wire PT100 resistive temperature sensor with two selectable temperature ranges. The unit can be configured for OVER or UNDER temperature and has an adjustment for temperature and hysteresis.

 

Features:

 

  • Fail-safe control feature
  • Direct connection to PT100 temperature sensor
  • Rear DIP switch selection of 2 temperature ranges
  • Potentio meter adjustable temperature setting
  • Potentiometer adjustable hysteresis setting
  • Power supply ON and Relay ON LEDs
  • Output 10A SPDT
Clear selection
Category:

Description

Sensor Specifications:

 

Probe Type Pt 100 3 wire (bridge 6 & 7 for 2 wire)
Probe Voltage 200mV
Short Circuit Current 1mA max
Standard Temperature -20 – 80°C
Ranges 80 – 180°C
Power Suppy AC Type (Galvanic) 110, 230, 400V, 525V ± 10% 50 / 60 Hz ± 5Hz
Isolation 4kV
Consumption ± 3VA
±6 VA 525 V

Supply Specifications:

 

Power Suppy AC Type (Galvanic) 110, 230, 400V, 525V ± 10% 50 / 60 Hz ± 5Hz
Isolation 4kV
Consumption ± 3VA
±6 VA 525 V

General Specifications:

 

Power ON Delay ≤ 300 ms
Power OFF Delay ≤ 200 ms
Indication for
Power Supply ON LED red
Output ON LED yellow
Environment
Degree Of protection IP 20
Operating Temperature -10 to + 50°C
Storage Temperature -50 to + 85°C
Weight 200g

Additional information

Supply Voltage

525Vac, 400Vac, 230Vac, 110Vac, 48Vac/dc, 24Vac/dc, 12Vac/dc

Reviews

There are no reviews yet.

Be the first to review “Temperature Controller – T1R”

Related products

One Shot Timer – T1P
One Shot Timer – T1P

Single function on-adjustable timer to initiate a 0.5 sec pulse on energization and/or de-energization. By bridging contacts 5 & 6 the relay will only pulse on application of the supply and by bridging out contract 6 & 7 the relay will only pulse when the supply is removed. The supply has to remain on for at least 3 seconds for the pulse on removing of power to function correctly. A 1 second pulse can be supplied on demand.

 
Features:
 
  • Selectable pulse on energization and/or de-energization
  • Non-adjustable pulse length of 0.5seconds (1sec on demand)
  • LED indication for power supply ON
  • Output 10A SPDT
R431.87 Select options This product has multiple variants. The options may be chosen on the product page
PLUGIN-TP2
Two Shot Timer – TP2

Microprocessor based two-shot timer with two selectable modes of operation and eight separately selectable ON and OFF time ranges from 0.3 sec - 60 hrs. The ON and OFF times can only be selected from the A or B range and not both.

 

Extensive applications due to combination of functions and time ranges. Due to the advanced design of the unit a high accuracy can be achieved. Any adjustment on the front potentiometers after the supply is applied is not acknowledged. This prevents unwanted changes of the time range.

 

The ON and OFF times can be adjusted independently.

 
Features:
 
  • Microprocessor based design
  • Time range 0.3sec – 60hrs
  • Rear DIP switch selection of 8 separate ON and OFF timer ranges
  • Separate potentiometer adjustable time settings for ON and OFF period
  • Selectable ON or OFF time first
  • Repeatable deviation: <0.2%
  • Power supply ON and Relay ON LEDs
  • Output SADPDT
R521.47 Select options This product has multiple variants. The options may be chosen on the product page
Pump Seal Protection – PSP1
Pump Seal Protection – PSP1

Microprocessor based monitoring relay to measure moisture in a submersible pump. Due to the advanced design of the unit a high accuracy and safety is achieved. Response delay are incorporated to prevent nuisance tripping. The unit energises on application of supply. If the current through the probes is more than 20uA or the resistance is smaller than 10 Mohm, the relay will de-energise after 10 sec. The relay will energise if the current is less than 15uA and the resistance is more than 1.4Mohm.

 
Features:
 
  • Microprocessor based design
  • High accuracy analogue converter
  • Repeatable deviation: <0.2%
  • Power supply ON and Relay ON LEDs
  • Output 5A DPDT
R424.70 Select options This product has multiple variants. The options may be chosen on the product page
PLUGIN-SC120
Signal Converters – SC120

Compact signal converter with built-in 24VDC power supply for the output. The unit is designed for low amplitude signals where isolation is not needed (use SI100 for isolation). A variety of inputs and outputs are available to suit most applications.

 
Features:
 
  • High linearity
  • On-board PSU
  • Choice of Inputs and Outputs
  • Low cost
  • Versatile
  • Power supply ON LEDs
R766.08 Select options This product has multiple variants. The options may be chosen on the product page